Home > Emulsion > Photopolymer Emulsion >

EDGE Silkscreen Photopolymer Emulsion

EDGE Silkscreen Photopolymer Emulsion


 
ADD TO CART: $27.00




Product Code: E-1010


Size for Edge*:


Qty:  
Overview
 

EDGE Silkscreen Photopolymer Emulsion

EDGE Silkscreen Photopolymer Emulsion is a One-Part, quick-drying, and fast-exposing photo-polymer emulsion. The EDGE Silkscreen Photopolymer Emulsion is one of the fastest-exposing emulsions available that may be used for plastisol, UV, and solvent ink systems. The Edge works best on the i-image unit and does not clog the filters as a lot of other one-part products do. the Edge does not clog the sewer system.


Highlights for EDGE Emulsion:

  • developed for plastisol, UV, and solvent ink systems
  • fast exposure
  • long shelf life
  • easy to re-claimer
  • very high resolution
  • zero pinholes if apply properly
  • excellent edge definition and bridging
  • is a one-part, ready-to-use textile emulsion and is recommended for plastisol inks and solvent inks.
  • offers durability & excellent image, due to its high solids & makeup.
  • yields a smooth, even coating, sharp edges, and high resolution.
  • Is based on SBQ technology & should only be handled in yellow light.
  • Saves time as it cures very fast & there is no need to add diazo.
  • Has good solvent resistance for most press wash & inkgradent for plastisol.
  • Offers all the properties of dual cure diazo base emulsion-so the shelf life is over one year.

Specification & Data

  • color: red
  • solids: 44%+-1%
  • viscosity: 9,000/10,000 cps at 20 rpm
  • solubility: water

GUIDELINE:
Before applying the emulsion to the screen, make sure that the screen is cleaned with a degreaser and dried thoroughly. Let the emulsion dry and then wash with a soft mist of water to create the image

EXPOSURE:
Distance for the exposure should be about one and a half times the diagonal measurement of the artwork from point light sources. Yellow and orange mesh require at least 50% more time than white mesh. The times given below are based on the white mesh at approximately 40 inches. METAL HALIDE 25 SECONDS 3000 WATTS CARBON ARC 20 SECONDS 60 AMPS FLUORESCENT TUBES 35-60 SECONDS 40 WATTS

Exposure times below were set for a 5 KW unit at 40" from the frame.


110 YELLOW POLYESTER MONO-FILAMENT MESH

*Coating Coater Suggested
Technique Edge Min. Exp. Time
1 BY 1 Round 27 sec.
1 BY 2 Round 30 sec.
1 BY 3 Round 40 sec.


230 YELLOW POLYESTER MONO-FILAMENT MESH
*Coating Coater Suggested
Technique Edge Min. Exp. Time
1 BY 1 Round 18 sec.
1 BY 2 Round 20 sec.
1 BY 3 Round 25 sec.



Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 2 Write a review »

  0 of 0 people found the following review helpful:
 
5 of 5 Excellent Value March 20, 2021
Reviewer: joyce coursey from Lyons, GA United States  
This emulsion is an excellent value. It offers great screen coverage with virtually zero pinholes. Very easy to use.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Heard it’s the best December 21, 2020
Reviewer: Octavia Holder from Lawrenceville, GA United States  
I haven’t used this as yet but my business piers say it’s the best

Was this review helpful to you?